High Quality & Reliable Medical Equipment supplier, CE, FDA Approval Equipment

  • My Cart

    Your cart is empty

    You have no items in your shopping cart.

Icon 100% Risk FREE:

30 day money back guaranty.

Icon Payment:

Through T/T, Western Union, get up to 3-8% discount. Contact us

Icon Shipment:

We can deliver to all over the world.

HL-WDI Dental Spot Welder

Be the first to review this product

HL-WDI Dental Spot Welder
Pin It

Usually will be shipped within 3-7 working days
We accept We accept PayPal, T/T(Telegraphic Transfer), Western Union


HL-WDI Dental Spot Welder

♦ Main characteristics of the machine:
• The electrode can be adjusted as different combination to suitable with different weldment.• The weld power can be adjusted, coarse regulation: three gears, fine regulation: continues.• The weld power display used latest light pillar type LED display.• The cover adopts fashion style and aesthetic in appearance.
 ♦ Main technique parameter:• Power supply: 220V±10%, 50Hz±1Hz or 110V, 60Hz

• The average input power: 0.1KVA• Energy storage: 2-50J• Rate of production: 15times/minute (MAX) 
♦ Structure:• Back of the machine has power switch, fuse tube and foot switch. Foot switch can used for start and stop welding.• At the front-panel left side of the machine, there's light pillar type display indicating size of energy,
  under LED display,it has a "Start" button, used for start and stop welding.• At the right side of the front-panel,there's power choice button (coarse regulation) and power adjust button (fine regulation)• There are two electrode arms,each has four electrodes.Vertically rotate to choose the suitable electrode combination,
   the electrode can rotate 90 degree to the right position automatically at each time.
   So it can make up different sets of electrode combination to adapt various different welding.• For some special welding, it can also use oxygen-free copper electrode bar.

Button introduce:

1) Light pillar type LED display   
2) the welding start button 
3) The press plate  
4) lower electrode arm 
5) Top electrode arm
6) top electrode
7) Lower electrode  
8) the power choice button (coarse regulation)
9) The power adjust button (fine regulation)
10) foot switch

♦ Operation method:• according to the welding choose suitable electrode, check the oxidize condition of the electrode,
   if it was oxidized, please sanding with sand paper or smooth file.• the weldment should be clean, no oxidization, without greasy dirt.• connect the power supply, turn on the power switch, and adjust "power choice button" according
  to the size and thickness of the weldment.• Press down the pressure plate, then relax the welding pressure pad slowly; make sure the top and
  bottom electrode compressed the weldment tightly. When the weldment at the right position press "Start "
  button or foot switch, it will finish welding once the display goes out. Release button, capacitance will be
  charge to appointed voltage (display lighten), take off the weldment and then continue next welding.• after welding, put discharging block (enclose with machine) between top and bottom electrodes,
  turn off the power supply, and press "Start" button to release energy. Adjust coarse regulation to lower range (I),
  counter-clockwise the fine regulation to minimum position.• If not use the machine, the top and bottom electrode should be separated, in order to avoid affection of the
  electrode because of long time connection.• LED light pillar display shows voltage, the size of light pillar refers to linear relation with voltage, and the welding
  energy refers to quadrate relation with voltage. The same size light pillar under the nuance, please use fine
  regulation to adjust the right position.

♦ Announcement: • Must use the single-phase three-pin power supplies, guarantee that the case of the machine connect to the earths to
  insure safety.• Put the machine to the dependable place.• Use AC stabilized supply, if possible, since it can guarantee the welding power stability, and reduce affection to other
  electric appliance.• The electrode must be rotated with clockwise.• When adjust the power, it can put discharge block between electrodes, press welding start button one time to release the
  remaining energy, so that make sure the next regulation be correct.• When the welding power is big, or the weld material get in bad connect, please prevent the splash thing burning human body, 
  the operator must use the protective glasses and protection gloves.• After using, wipe the machine clean, put it at dry ,well-ventilated and no causticity air indoor place.• When the machine breaks down, contact with the factory or sent repair by the professional person in time.

♦ The enclosure general chart (parts list)• 1×Main machine
• 1× Power cable   
• 1×Foot switch  
• 2×Fuse 5A  
• 1×Discharging block
• 1×Warranty card
• 1×Certificate   
• 1×Manual 

Additional Information


Write Your Own Review

You're reviewing: HL-WDI Dental Spot Welder

How do you rate this product? *

 1 star2 stars3 stars4 stars5 stars

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

You may also be interested in the following product(s)